In the whole process of video post production, there are several aspects to pay special attention to, such as: interface output, cutting, patching, mounting, covering sub film and so on. All the mistakes in the design and production of inkjet advertising lead to the success and failure of inkjet advertising. Next, we will give you a detailed introduction to the problems that we must pay attention to in the process of production in the later stage.
1、噴繪廣告宣傳輸出:針對圖象的輸出,精密度關重要,歐帆對全部廣告宣傳的精密度制做,全是1440DPI,確保了界面的真實復原。顏色輸出規定為CMYK,顏色復原度提高。
1. Print advertising output: for image output, precision is very important. Oufan's precision of all advertising is 1440dpi, which ensures the real restoration of the interface. The color output is specified as CMYK, and the color recovery is improved.
2、噴繪廣告宣傳裁剪:針對界面尺寸與打印紙張相距很大需裁剪的,需要量剪齊整。在大家裁膜時,也運用剪子順著道路標線走齊,由于會便捷在覆亞膜中的上膜工作中,且更能保質保量與通過率。
2. Inkjet advertising cutting: for the interface size and printing paper is far from the need to cut, the amount of cutting neat. When you cut the film, you also use the scissors to go along the road marking, because it will be convenient to apply the film in the covering sub film, and it can guarantee the quality and quantity and pass rate.


3、噴繪廣告宣傳拼湊:廣告宣傳界面的拼湊部位要搞清楚,界面左右部位明確好。在輸出全過程中,由于要輸出的界面是同一張圖,因而盡量維持其顏色一致和尺寸相對,要紀錄輸出時的設定參改,保證準確無誤。
3. Inkjet advertising patchwork: the patchwork of advertising interface should be clear, and the left and right parts of the interface should be clear. In the whole process of output, since the interface to be output is the same picture, the color and size of the interface should be consistent as far as possible, and the setting parameters should be recorded to ensure accuracy.
4、噴繪廣告宣傳裱板:為了更好地使界面的四邊完好無損的宣傳欄邊沿符合,大家先將界面沿在其中的相鄰兩側裁齊,然后此后兩側為標準,兩端對齊宣傳欄的邊沿。用裁紙刀沿宣傳欄的卡條,將界面不必要的一部分裁去,即把整副畫裱完。
4. Spray painting advertising mounting board: in order to make the edges of the billboard with intact four sides of the interface conform to each other, we first cut the interface edge on the adjacent two sides, and then the two sides are the standard, and the two ends are aligned with the edge of the billboard. Use a paper cutter to cut the unnecessary part of the interface along the card bar of the bulletin board, that is, to mount the whole picture.
5、噴繪廣告宣傳界面覆亞膜:噴繪廣告宣傳為了更好地維持實際效果,會在廣告宣傳外開展覆亞膜。覆亞膜時是調整滾子軸承的旋扭,拿到覺得沒有摩擦阻力才行、微緊。廣告宣傳界面覆亞膜將膜平整送進,確保在膜行走的全過程中不造成側偏,膜沒有受擠壓成型狀。隨后,將膜拉上,在膜將要停止時,將滾子軸承控住,用勁拉一下膜,確保頂端齊平。
5. Sub film covering of ink-jet advertising interface: in order to better maintain the actual effect, sub film covering will be carried out outside the advertising. When covering sub film, it is the first to adjust the rotation and torsion of the roller bearing, so that it can be slightly tight without friction resistance. The advertising interface is covered with sub film to send the film smoothly to ensure that the film does not deviate during the whole process of walking, and the film is not extruded. Then, pull the film up. When the film is about to stop, hold the roller bearing and pull the film hard to ensure that the top is flush.
以上是關于在制作噴繪廣告后期時需注意的問題,希望對大家有所幫助,如想要了解更多內容歡迎點擊濟南噴繪廣告公司https://www.m.tb10.cn官網。
The above is about the production of ink-jet advertising needs to pay attention to the problem, hope to help you, if you want to know more, welcome to Jinan spray painting advertising company https://www.m.tb10.cn Official website.




